OWC OWCDIDIMM11D2 Installationshandbuch

Mac mini 2011-20122nd Hard DriveInstallation Manual

2 DisassemblyLooking from the front of the Mac mini, locate the power supply plug and disconnect it from the logic board. You can either use the green

2 DisassemblyOnce you have removed the logic board, the chassis will be exposed.Remove the 2 Torx T6 screws that secure the hard drive carrier and pow

Remove the upper hard drive from the hard drive carrier. It will just lift out.Look at the back of the Mac mini and locate the power port. Inside the

Grasp the power plug with your ngers and turn it 90˚ counterclockwise until it releases from the Mac mini chassis. 2 Disassembly⤹Slide the power supp

2 DisassemblyLift up on the hard drive carrier and remove it from the Mac mini chassis.㉛Mac mini 2011-2012 2nd Hard Drive Kit

3 DRIVE CARRIER ASSEMBLY3 Drive Carrier AssemblySet the drive carrier in front of you with the mounting tabs pointed away from you.Insert the 4 rubbe

3 Drive Carrier AssemblyRemove your drive from it’s packaging.Insert the ex cable into the SATA port on your drive.③④Mac mini 2011-2012 2nd Hard Driv

3 Drive Carrier AssemblyMake sure that the ex cable is correctly oriented and then insert the drive into the drive carrier as shown. Insert the 4 in

Place the drive carrier back into the Mac mini housing and replace the left Torx T6 screw from step 25. The mounting tabs for the drive carrier will l

4 AssemblyLine the power plug up so that the locking tab is in the inside mounting groove in the Mac mini chassis. Twist the power plug 90˚ clockwise

Mac mini 2011-2012 2nd Hard Drive Kit Table of Contents 5.1 FAQ1 INTRODUCTION2 DISASSEMBLY3 DRIVE CARRIER ASSEMBLY6 CUSTOMER SERVICE5 FAQ4 ASSE

4 AssemblyGently slide the logic board assembly back into the Mac mini chassis. Stop when you reach the side locking tabs.⑦Looking from the front of t

4 AssemblyTurn the Mac mini back around so you are looking from the rear ports. Line up the SATA connectors so that they are not going to interfere wi

4 AssemblyReplace the Torx T6 screw into the logic board.Reinstall the fan cowling and insert the short T6 screw that you removed.⑪⑫⑬⤹Mac mini 2011-20

4 AssemblyUsing the Torx T8 screwdriver, insert the 3 2mm hex head (the Torx is the same size as a 2mm or 5/64 hex bit) screws that are used to hold t

4 AssemblyReplace the 3 Torx T-6 screws that secure the exhaust fan from the chassis of the Mac mini.The lower right screw is a long stando screw. Th

You’re all set! Reconnect your Mac mini and congure your new hard drive. Replace the bottom cover of your Mac mini.Replace the 2 SO-DIMMs

•Visit our tech center for more support suggestions, including FAQs.http://eshop.macsales.com/tech_center/index.cfmIf you still need support, please h

This page left blank intentionally

Copyrights:Copyright © 2012-2013 Other World Computing, Inc. All rights reserved. OWC is a registered trademark of Other World Computing. Other World

1 INTRODUCTION1 IntroductionYour computer is a static-sensitive device. It is susceptible to invisible damage if not protected during installation. W

2 DISASSEMBLY2 DisassemblyBegin by placing your Mac mini upside down on a at surface.It is recommended that you use a towel or mousepad to protect t

2 DisassemblyRemove the 3 Torx T-6 screws that secure the exhaust fan from the chassis of the Mac mini.The lower right screw is a long stando screw.

2 DisassemblyUsing the Torx T8 screwdriver, remove the 3 2mm hex head (the Torx is the same size as a 2mm or 5/64 hex bit) screws that are used to hol

2 DisassemblyRemove the Torx T6 screw from the fan cowling. The cowling will easily come o once the screw is out. Set it aside to proceed.Using the g

2 DisassemblyDisconnect the IR board cable by lifting up on the connector body from behind using the green pry tool. Be extremely careful as VST conn

2 DisassemblyInsert the logic board removal tool into the 2 holes on the logic board. The tool will go all the way down through the holes. Conrm tha